Thermal hazard assessment of TKX-50-based melt-cast explosive

In the present study, thermal hazards of TNT and DNAN used as the molten binder in TKX-50-based melt-cast explosives were comparatively studied through accelerating rate calorimeter (ARC) and Cook-off experiments. Two kinds of ARC operation modes were performed to investigate the thermal safety performance under adiabatic conditions (HWS mode) and constant heating (CHR mode). The obtained results demonstrated that at both heating modes, DNAN/TKX-50 outperformed TNT/TKX-50 from the thermal safety point of view. However, the sensitivity to heat of the samples was reverse because of the different heating modes. In addition, the results of thermal hazard assessment obtained from the cook-off experiment complied with ARC analysis which indicated the molten binder TNT replaced by DNAN would reduce the hazard of the TKX-50 melt cast explosive. Furthermore, the results of cook-off experiments also showed that DNAN/TKX-50 outperformed TNT/TKX-50 from the aspect of thermal stability, which was consistent with the result of CHR mode because of the similar heating process.     

Analysis on damage characteristics and detonation performance of solid rocket engine charge subjected to jet

To further explore the damage characteristics and impact response of the shaped charge to the solid rocket engine (SRE) in storage or transportation, protective armor was designed and the shelled charges model (SCM)/SRE with protective armor impacting by shaped charge tests were conducted. Air overpressures at 5 locations and axial acceleration caused by the explosion were measured, and the experimental results were compared with two air overpressure curves of propellant detonation obtained by related scholars. Afterwards, the finite element software AUTODYN was used to simulate the SCM impacted process and SRE detonation results. The penetration process and the formation cause of damage were analyzed. The detonation performance of TNT, reference propellant, and the propellant used in this experiment was compared. The axial acceleration caused by the explosion was also analyzed. By comprehensive comparison, the energy released by the detonation of this propellant is larger, and the HMX or Al particles contained in this propellant are more than the reference propellant, with a TNT equivalent of 1.168–1.196. Finally, advanced protection armor suggestions were proposed based on the theory of woven fabric rubber composite armor (WFRCA).     

钢丝增强复合条带抗弹性能数值分析

为研究钢丝增强聚合物基复合条带的抗弹性能,基于冲击动力学理论分析其抗弹机理,再借助ANSYS/LS-DYNA软件和LS-PrePost前后处理器模拟有无增强钢丝2种工况下,条带对7.62 mm弹体的冲击响应。分析表明：条带的弹性模量、剪切模量和面密度会影响其能量吸收性能,能量吸收量随三者的增大而增大;由于聚合物基体的正交各向异性,应力云图显示出扁平椭圆状是合理的;在聚合物基复合条带中嵌入增强钢丝对条带整体的抗弹性能有积极的影响,但嵌入过量的钢丝会导致重量和成本的增加,因此需要对合理的钢丝配比率作进一步研究。研究结果可为钢丝增强聚合物基复合条带在野战防护结构中的应用提供参考。     

综合飞行/火力控制系统性能评价

详细介绍了综合飞行 /火力控制系统 (IFFCS)性能评价的方法。该方法把评价过程分为单元评价、组合评价和系统性能评价 ,将系统性能指标逐层分解 ,以保证闭合系统最终能完成自动攻击任务。以高性能控制系统仿真软件MATTRIXX6 .0为平台 ,按此方法开发的评价软件获得了用户的认可     

高原环境对军用油料装备柴油动力性能影响分析

针对青藏高原特殊地理环境和气候条件特点,通过某大型群车加油车在高原地区的训练使用,分析海拔高度与大气压力、空气密度和温度的对应关系,探讨了在高原环境条件下使用油料装备其柴油动力的动力性、经济性及低温起动性能受到的影响,提出了相应的改进措施。     

基于频谱分析的飞行模拟器飞行性能验证

介绍频谱分析用于仿真系统模型验证的原理和方法,提出一种应用频谱分析进行飞行模拟器飞行性能验证的方案。结合飞行试验和仿真模型的输出数据,分别采用窗谱估计和最大熵谱估计方法对某型飞行模拟器的飞行性能进行验证,并对验证结果进行分析。结果表明,频谱分析法用于飞行模拟器飞行性能的验证是有效的,可为其他训练模拟器的性能验证提供参考。     

准静态受遮蔽的Rician衰落信道中空时格码的性能上界

针对准静态受遮蔽的 Rician 衰落信道,在收端已知信道状态信息的条件下,文中分析了空时格码的性能.推导了码字差相关阵为对角阵的空时格码系统的成对差错概率的确切表达式,得到了相应空时格码在准静态受遮蔽的 Rician 衰落信道中的性能上界。仿真结果表明,在遮蔽不太严重的信道中,文中得到的 union 界与相应编码系统的实际性能有很好的近似度。     

气动式振动台气锤产生激励信号的机理及其性能研究

建立了阶梯式活塞气锤的力学模型,揭示了该类气锤产生碰撞信号的机理,针对两种不同型号的气锤,结合大量工程实验仿真生成了不同气压作用下两种气锤产生的激励信号,以激励信号的低频能量为气锤的性能指标,进一步评价了两种气锤的性能优劣.研究结果表明:大气锤的性能明显优于小气锤的性能.     

固定翼反潜巡逻机作战效能评估

运用改进的Topsis评估模型对反潜巡逻机的作战效能进行评估,主要是对指标权重的计算方法进行改进:综合考虑客观熵权和专家主观权重得到综合权重,通过客观的熵权信息来调整主观权重的偏差,使得反潜巡逻机作战效能的评价结果更为合理。实例分析表明,该方法能够主客观相结合,简单有效,具有一定的推广应用价值。     

浅析小型史馆建筑内部展示造型与多媒体表现

作为现代展览展示建筑的一个发展分支，小型史馆就是一部精练的“物化”历史，表达出一个丰富而统一的信息传播展示空间。小型史馆的设计往往在有限的空间内，充分体现出观演类建筑的主要特点，其内部的展示造型设计和多媒体表现手段起到了重要的作用。主要从小型史馆建设出发，对其内部展示造型设计与多媒体表现手段进行分析与探讨，阐述了它们的设计手法及达到的视觉创意效果。